Airtech
Published

What a difference a year makes

If 2020 was bad, then 2021 can only be better. CW Editor-in-Chief Jeff Sloan discusses the promising and not-so-promising industry trends leading up to 2021. 

Share

Boat stock image

Photo Credit: Getty Images

Although it is objectively true that 2020 is, on balance, one of the worst years of the last century lived by humans, it will be quite a while before we understand thoroughly how history will judge the Year of the Pandemic.

However, now that the year is officially in the rearview mirror, and now that the distribution of vaccines is providing us a slight glimpse of what might be the faintest glimmer of a light at the end of the COVID-19 tunnel, we might start thinking about what 2020 has wrought, and what it means for the composites industry.

First, we should acknowledge the asynchronous nature of the economic downturn that the coronavirus pandemic wrought. Unlike a traditional recession, which strikes broadly and uniformly, the brakes applied to the composites industry by COVID-19 were not felt homogeneously.

The wind energy industry, for example, after a short lull in the spring when pandemic-induced shutdowns began, soon returned to pre-COVID-19 form and is expected to end 2020 in record-setting fashion. The American Wind Energy Assn. (AWEA, Washington, D.C.) reported in October 2020 that the third quarter of 2020 saw the U.S. install 2,000 megawatts (MW) of wind power — a record for any third quarter in the U.S. Further, the U.S. was on pace to install more wind power in 2020 than any previous year, with installations through the third quarter up 72% compared to the same period in 2019. Much of this activity likely was spurred by the Production Tax Credit (PTC), which expired on Dec. 31, 2020, but that should not diminish our admiration for what the entire wind industry supply chain accomplished in very difficult circumstances.

Similarly, with the downturn in air travel, and with governments limiting indoor gatherings, many people sought outdoor activities for leisure pursuits and to safely escape the pandemic. Thus, recreational vehicle (RV), recreational marine, bicycle and fishing rod sales increased significantly. The RV Industry Assn. (RVIA, Reston, Va., and Elkhart, Ind., U.S.) in September 2020 reported that shipments of RVs were expected to have surpassed 400,000 wholesale units in the U.S. by the end of 2020 (a 4.5% increase over 2019) and see continued growth in 2021 to more than 500,000 units. 

The National Marine Manufacturers Assn. (NMMA, Chicago, Ill., U.S.) reported in October 2020 that power boat retail sales had increased 8% year to date (YTD) compared to the same period in 2019. Sales of personal water craft (PWC), pontoons and freshwater fishing boats were up 2%, 9% and 10% respectively YTD, while sales of saltwater fishing boats, tow boats, cruisers and yachts each had growth ranging from 11% to 15%, compared to 2019.

The pandemic also clarified and possibly accelerated some trends in the automotive industry that were already at work. The most notable is the global shift away from internal combustion engine (ICE) vehicles and toward electric vehicles (EV). The International Energy Agency (IEA) says overall passenger vehicle sales in 2020 are expected to drop about 15% compared to 2019, but that EV sales will be flat. And Bloomberg NEF says the EV average vehicle price will drop below the average ICE vehicle price by 2025, and that EV sales will exceed ICE vehicle sales by 2037. CW columnist Dale Brosius outlines the EV opportunity for the composites industry in greater detail. 

If wind, recreation and EV sales are the silver lining, then the darkest, biggest cloud of 2020 is the aerospace industry, which, by value, is the most important end market served by the composites industry. Passenger air travel has been so diminished by the pandemic that one can say, with substantial confidence, that things can only get better. But even that will take time, led first by a recovery in domestic air travel, followed by 2025 or so, a return to “normal” international air travel. Aviation Week, in a mid-December forecast, said to expect new global commercial aircraft deliveries to increase to about 1,350 in 2021, followed by incremental annual increases through 2030. Still, an estimated output of 1,750 by that year takes us back to 2017 levels only, and a far cry from the 2018 high-water mark of 1,800+ aircraft. Still, it’s an enouraging return to growth. 

The big question facing the aerospace industry now is if and when a new aircraft program might be announced. And who might announce it. I will address that next month. In the meantime, happy 2021, and stay safe.

ELFOAM rigid foam products
Custom Hydraulic Press Manufacturing
Wabash
Greenerd Compression Molding
Kent Pultrusion
Toray Advanced Composites hi-temperature materials
CompositesWorld
Composites One - distributor

Related Content

Aerospace

Achieving composites innovation through collaboration

Stephen Heinz, vice president of R&I for Syensqo delivered an inspirational keynote at SAMPE 2024, highlighting the significant role of composite materials in emerging technologies and encouraging broader collaboration within the manufacturing community. 

Read More
Editorial

The (not exactly) new guy at CW

Former CW writer and editor Scott Francis rejoins the brand as editor-in-chief as Jeff Sloan assumes the role of publisher. 

Read More

Celebrating 10 years of CAMX

In the years since its establishment, CAMX has a lot to offer industry, merging industry segments and trends with a variety of networking and educational opportunities to provide a comprehensive platform that everyone can benefit from.

Read More
Editorial

Who's ready for the Olympics?

With the 2024 Summer Olympics in Paris, this year’s JEC World is bound to be abuzz with talk of this year’s event — from the use of composites in sporting equipment to the roles they play in AAM.

Read More

Read Next

Finishing & Fastening

“Structured air” TPS safeguards composite structures

Powered by an 85% air/15% pure polyimide aerogel, Blueshift’s novel material system protects structures during transient thermal events from -200°C to beyond 2400°C for rockets, battery boxes and more.

Read More
Compression Molding

VIDEO: High-volume processing for fiberglass components

Cannon Ergos, a company specializing in high-ton presses and equipment for composites fabrication and plastics processing, displayed automotive and industrial components at CAMX 2024.

Read More
Repair

Developing bonded composite repair for ships, offshore units

Bureau Veritas and industry partners issue guidelines and pave the way for certification via StrengthBond Offshore project.

Read More
Composites One - distributor